Devices You Need to Install a New Bath Tub
Devices You Need to Install a New Bath Tub
Blog Article
We've unearthed this article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the net and figured it made good sense to relate it with you in this article.
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old tub with a brand-new one is also a reasonably hard job. If the old bathtub is readily easily accessible, the task can move easily; if you need to open a wall surface to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. See to it you have actually qualified on your own for the job as well as are comfortable trying it. Rather than working with a contractor to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This write-up will aid you install a brand-new bathtub in your shower room if you have actually already gotten a new tub and also don't need to transform the arrangement of your previous water system pipes.
Your tools and also material checklist must comprise the following:
Planning for the Setup
To start with, the supporting framework provided with the bathroom should be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the restricted access that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub until the level reads degree.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the various other tap.
Activate the supply of water and also check all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the tub needs to wait up until the bath tub has been made use of at the very least once as this will resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area in between the tap as well as the sink. Secure the faucet in position with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap adapters. The previous type should be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, resulting in issues with moisture as well as possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealant can crack rather early if you do not take into account this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Make a remark further down. We will be delighted to find out your opinion about this blog. Hoping to see you back again in the future. Liked our write up? Please share it. Help other people check it out. Bless you for your time. Come back soon.
Click Here
Report this page